How To Repair Four Wheeler That Has Cooler Motor On It

Riding around in an ATV is ane of the all-time experiences 1 tin have. Driving around new landscapes without the worry about roads is a bully feeling. However, it is not all fun and games, as an ATV is all the same a vehicle that tin have problems or break down. ATVs face fifty-fifty more than risks than the usual vehicle due to the common off-route driving. Submerging or sinking your ATV is i of these risks that can crusade a lot of damage to an ATV. That is why it is important to know what to practise when you sink your four-wheeler; though, using four-wheeler snow tracks tin help prevent sinking in all sorts of terrain.

Bike Out of Water

The commencement thing to do afterwards an ATV becomes submerged is to make sure the rider is alright. Check for injuries and deal with them appropriately. The first footstep after that is to get the ATV out of whatever information technology is submerged in. To get-go this process, you will need to turn off the ATV. Practise not attempt to turn the ATV back on until yous have gone through the steps you need to fix the vehicle. In one case the 4-wheeler is off, put information technology into neutral to allow the wheels to turn without power. The last thing to practise is to pull the ATV out with a winch or another vehicle that tin claw up to it. Do not endeavor to utilize only your ain strength to avert pain yourself.

Air Filter

One time the ATV is no longer submerged, you will need to have out the air filtration box equally information technology unremarkably filters air going to the engine. Withal, it can fill up with liquid in these kinds of incidents; removing information technology will prevent liquid from leaking into the engine. Removing the air filter can exist a bit unlike on each ATV model, so make sure you know how to practise it for your model. It often requires that yous remove the seat to get access to the air filtration box. You need to drain the box of whatever liquid and let it fully dry. It is also possible that yous will need a new filter for the box and peradventure a new filter box if you cannot clean information technology fully.

Tilt the Wheel

This step volition most likely require few friends for aid. You now need to drain all the liquid you can from the motor and the exhaust. The best style to exercise this is to tilt the bike astern, and then the front of the cycle points up. If there is liquid in the motor and exhaust system, you should see information technology drain out as you lift the ATV. You lot can put the vehicle down one time the liquid stops draining from information technology. The ATV should be ready for a tow to wherever you need information technology for the next office of the repair process.

Cleaning the Air System

Once you have the ATV settled in a workspace, y'all will desire to commencement cleaning out the air inlet. This procedure changes a fleck depending on the model, but you will demand to clear out any mud, grime, and liquid from the inlet. This will aid to prevent any engine damage when using the ATV later. You will also demand to detach the breather tubes to wash them with water. Let them dry fully before putting them back together.

Stator

The stator is a mutual place for liquid to gather when a vehicle is waterlogged. To clean the stator, you demand to start with removing the cover on information technology. Use some course of air compressor or liquid vacuum to remove all the liquid y'all can from the stator. Afterward you lot remove all the liquid you can, use a hot air blower, like a hairdryer, to dry any of the remaining liquid. Do this advisedly, equally hot air can impairment some parts of the stator. You tin too let the stator airdry, just this can have a while.

Belt Housing

If your bike has a belt transmission, you lot will need to drain it of any liquid that got in. the method of draining changes based on the model of ATV, but almost have a drain plug. If there is no bleed plug, you will demand to open up the housing cover to clean it of whatsoever liquid. You lot may have to do this if the liquid that is in your ATV is not just water.

Replacing Liquids

Whatever liquid that gets into an ATV volition often contaminate the cooling system, the gas tank, and the carburetor. You will demand to drain and clean each one of these parts multiple times to get your ATV back in working order. The carburetor often needs actress attention and is worth removing to fully clean. Once everything is dorsum in place, you should refill the vehicle with the recommended liquid.

Drain the Cylinder

To bleed the cylinders of whatsoever liquid that has gathered, y'all volition need to remove all the spark plugs and plug wires. This will foreclose possible harm to the engine during the next steps. Now, showtime to turn the engine several times until liquid stops leaving the cylinders. In one case tuckered, put all the parts dorsum where they belong and let the ATV idle for a few minutes. Apply lubricant to the air inlet as it idles to replace whatever lost lubricant. The ATV may fume as information technology idles, merely this is non something to worry most, as long as information technology stops after a few minutes.

Supercede Spark Plugs

It is not unusual to have ruined spark plugs after submerging an ATV. Become a few spark plugs and replace your old ones. Every bit you lot start up the vehicle, some remaining liquid might damage your new spark plugs— only replace these as needed. Keep going until the cycle can fully showtime and you see the spark plugs working properly.

Final Fluid Replacement

Before taking your ATV out for another trip, you lot will need to replace whatsoever other contaminated fluids. Yous will near likely demand to check the engine oil for contamination. If information technology needs to be replaced, utilize inexpensive diesel to clear out the bad oil and drain it. Repeat this process until the diesel oil is clear when y'all bleed it. You can also echo this process with cheap engine oil a few times and then supervene upon it with the kind of oil you lot want in your engine. Yous will need to cheque the differentials and transmission for dirty oil as well. If muddy, you volition have to drain it and supplant information technology with cheap oil like the engine. Once the cheap oil drains clear, you can fill upwardly with your normal oil. Replacing the brake fluid requires no test or cleaning. Simply bleed the bad brake fluid and pour in new restriction fluid at the same fourth dimension to preclude air from inbound the system. Stop draining fluid once you lot come across clean brake fluid start to drain.

Once you take done all these steps, your ATV should exist ready to drive once again. It can exist quite a hassle to deal with a submerged ATV, merely that is why it is so important to know what to practice when yous sink your iv-wheeler. When you are all done, you should but be out a few hours to fully fix your ATV if you have the role.

What To Do When You Sink Your Four Wheeler